Topic break down
Topic 2, Cisco Data Center Infrastructure—Cisco NX-OS
Question No : 1 - (Topic 2)
Nexus# conf t
Enter configuration commands, one per line. End with CNTL/Z.
Nexus(config)# interface Loopback10
% Permission denied
Nexus(config)# ?
no Negate a command or set its defaults
username Configure user information.
end Go to exec mode
exit Exit from command interpreter
What is the reason why this user is not able to enter configuration commands?
A. The user did not enter enable prior to going into configuration mode.
B. The software license installed on Nexus is Layer 2 only, which does not allow the
creation of Layer 3 interfaces.
C. The user RBAC role is set to network-operator.
D. The user failed authentication and user access defaulted to read-only mode.
E. The AAA server is currently not responding.
Answer: C
Question No : 2 - (Topic 2)
On a Cisco Nexus 7000 Series Switch, what is the purpose of this command?
switch# config terminal
switch(config)# mac address-table learning-mode conversational vlan 1-10
switch(config)#
A. Enable conversational learning on FabricPath vlans 1-10 for F-Series module
B. Enable FabricPath protocol on VLANs 1–10
C. No need for this command as conversational learning is enabled by default for all VLANs.
D. Enable conversational learning on Classical Ethernet VLAN for F-Series module
Answer: D
Question No : 3 - (Topic 2)
What are two benefits of a FabricPath network? (Choose two.)
A. Simplicity of configuration
B. Automatic OSPF routing
C. Scalability
D. Dynamic link selection
E. Spanning tree loop prioritization.
Answer: A,C
Topic 3, Cisco Storage Networking
Question No : 4 - (Topic 3)
When a switch that supports enhanced zoning joins a fabric, which SW_ILS command does it use to determine the enhanced zoning capabilities of the other switches in the
fabric?
A. MR
B. ESS
C. ELP
D. EFP
E. none of the above
Answer: B
Question No : 5 - (Topic 3)
When building a NIC team (virtual port channel) between a host and a pair of Cisco Nexus 5000 Series Switches that will carry FCoE traffic, what is the maximum number of physical links that can exist in the team?
A. 1
B. 2
C. 4
D. 5
E. 16
Answer: B
Topic 5, Cisco Unified Computing System
Question No : 6 - (Topic 5)
How many virtual interfaces do the Cisco UCS 1280, 1240, and 1225 Virtual Interface Cards support?
A. 128
B. 64
C. 256
D. 1024
E. 100
Answer: C
Question No : 7 - (Topic 5)
Fault suppression allows you to suppress SNMP trap and Call Home notifications during a planned maintenance period. Which three commands are necessary to activate this suppression polices in Cisco UCS Manager? (Choose three.)
A. default-chassis-all-maint
B. default-chassis-phys-maint
C. default-fex-all-maint
D. default-FI-phys-maint
E. default-blade-phys-maint
F. default-vic-phys-maint
Answer: A,B,C
Question No : 8 - (Topic 5)
Which two statements about end-host mode in SAN connectivity in a Cisco UCS environment are true?
(Choose two.)
A. End-host mode is synonymous with NPV mode.
B. In end-host mode, only hard pinning of vHBAs to Fibre Channel uplink ports is allowed.
C. Making configuration changes between Fibre Channel switching mode and end-host mode is nondisruptive.
D. End-host mode is the default Fibre Channel switching mode.
Answer: A,D
Topic 6, Cisco Application Networking Services
Question No : 9 - (Topic 6)
Refer to the exhibit.
Which command would produce this output?
A. show stats HTTP
B. show stats load balance
C. show stats probe type
D. show parameter map
Answer: B
Question No : 10 - (Topic 6)
A load balancer performs an operation on a predefined parameter, such as the IP address, HTTP cookie, or URL, when a new connection is made so that another connection with the same parameter will always reach the same server. Which load-balancing predictor does this statement describe?
A. round robin
B. least-connections
C. hashing
D. least-loaded
Answer: C
No comments:
Post a Comment